wHAT IS Hard disk drive?

What is Hard disk drive?

A hard disk drive (HDD), commonly referred to as a hard drive, hard disk or fixed disk drive, is a non-volatile storage device which stores digitally encoded data on rapidly rotating platters with magnetic surfaces. Strictly speaking, "drive" refers to a device distinct from its medium, such as a tape drive and its tape, or a floppy disk drive and its floppy disk. Early HDDs had removable media; however, an HDD today is typically a sealed unit with fixed media.

HDDs were originally developed for use with computers. In the 21st century, applications for HDDs have expanded beyond computers to include digital video recorders, digital audio players, personal digital assistants, digital cameras and video game consoles. In 2005 the first mobile phones to include HDDs were introduced by Samsung and Nokia. The need for large-scale, reliable storage, independent of a particular device, led to the introduction of configurations such as RAID arrays, network attached storage (NAS) systems and storage area network (SAN) systems that provide efficient and reliable access to large volumes of data.

HDDs record data by magnetizing ferromagnetic material directionally, to represent either a 0 or a 1 binary digit. They read the data back by detecting the magnetization of the material. A typical HDD design consists of a spindle which holds one or more flat circular disks called platters, onto which the data is recorded. The platters are made from a non-magnetic material, usually glass or aluminum, and are coated with a thin layer of magnetic material. Older disks used iron(III) oxide as the magnetic material, but current disks use a cobalt-based alloy.

The platters are spun at very high speeds. Information is written to a platter as it rotates past mechanisms called read-and-write heads that operate very close over the magnetic surface. The read-and-write head is used to detect and modify the magnetization of the material immediately under it. There is one head for each magnetic platter surface on the spindle, mounted on a common arm. An actuator arm (or access arm) moves the heads on an arc (roughly radially) across the platters as they spin, allowing each head to access almost the entire surface of the platter as it spins. The arm is moved using a voice coil actuator or (in older designs) a stepper motor.

The magnetic surface of each platter is divided into many small sub-micrometre-sized magnetic regions, each of which is used to encode a single binary unit of information. In today's HDDs each of these magnetic regions is composed of a few hundred magnetic grains. Each magnetic region forms a magnetic dipole which generates a highly localized

magnetic field nearby. The write head magnetizes a magnetic region by generating a strong local magnetic field nearby. Early HDDs used an electromagnet both to generate this field and to read the data by using electromagnetic induction. Later versions of inductive heads included metal in Gap (MIG) heads and thin film heads. In today's heads, the read and write elements are separate but in close proximity on the head portion of an actuator arm. The read element is typically magneto-resistive while the write element is typically thin-film inductive.

In modern drives, the small size of the magnetic regions creates the danger that their magnetic state be lost because of thermal effects. To counter this, the platters are coated with two parallel magnetic layers, separated by a 3-atom-thick layer of the non-magnetic element ruthenium, and the two layers are magnetized in opposite orientation, thus reinforcing each other. Another technology used to overcome thermal effects to allow greater recording densities is perpendicular recording, which has been used in many hard drives as of 2007.

Hard disk drives are sealed to prevent dust and other sources of contamination from interfering with the operation of the hard disks heads. The hard drives are not air tight, but rather utilize an extremely fine air filter, to allow for air inside the hard drive enclosure. The spinning of the disks causes the air to circulate forcing any particulates to become trapped on the filter. The same air currents also act as a gas bearing which enables the heads to float on a cushion of air above the surfaces of the disks.

Capacity and access speed

Using rigid disks and sealing the unit allows much tighter tolerances than in a floppy disk drive. Consequently, hard disk drives can store much more data than floppy disk drives and can access and transmit it faster. In 2007, a typical “enterprise”, i.e. workstation HDD, might store between 160 GB and 1 TB of data (as of local US market by July 2007), rotate at 7,200 or 10,000 revolutions per minute (RPM) and have a media transfer rate of 1 Gbit/s or higher. The fastest “enterprise” HDDs spin at 15,000 rpm, and can achieve sequential media transfer speeds above 1.6 Gbit/s. Mobile, i.e., laptop HDDs, which are physically smaller than their desktop and enterprise counterparts, tend to be slower and have less capacity. In the 1990s, most spun at 4,200 rpm. In 2007, a typical mobile HDD spins at 5,400 rpm, with 7,200 rpm models available for a slight price premium.

The exponential increases in disk space and data access speeds of HDDs have enabled the commercial viability of consumer products that require large storage capacities, such as digital video recorders and digital audio players. In addition, the availability of vast amounts of cheap storage has made viable a variety of web-based services with extraordinary capacity requirements, such as free-of-charge web search and email (Google, Yahoo!, etc.).

The main way to decrease access time is to increase rotational speed, while the main way to increase throughput and storage capacity is to increase areal density. A vice president of Seagate Technology projects a future growth in disk density of 40% per year. Access times have not kept up with throughput increases, which themselves have not kept up with growth in storage capacity.

As of 2006, some disk drives use perpendicular recording technology to increase recording density and throughput.

The first 3.5" HDD marketed as able to store 1 TB was the Hitachi Deskstar 7K1000. It contains five platters at approximately 200 GB each, providing 935.5 GiB of usable space. Hitachi has since been joined by Samsung (Samsung SpinPoint F1, which has 3 × 334 GB platters), Seagate and Western Digital in the 1 TB drive market.

Form factor	Width	Largest capacity	Platters (Max)
5.25" FH	146 mm	47 GB (1998)	14
5.25" HH	146 mm	19.3 GB (1998)	4
3.5"	102 mm	1 TB (2007)	5
2.5"	69.9 mm	500 GB (2008)	3
1.8" (PCMCIA)	54 mm	160 GB (2007)
1.8" (ATA-7 LIF)	53.8 mm
1.3"	36.4 mm	40 GB (2008)	1

Capacity measurements

The capacity of an HDD can be calculated by multiplying the number of cylinders by the number of heads by the number of sectors by the number of bytes/sector (most commonly 512). Drives with ATA interface bigger and more than eight gigabytes behave as if they were structured into 16383 cylinders, 16 heads, and 63 sectors, for compatibility with older operating systems. Unlike in the 1980s, the cylinder, head, sector counts reported to the CPU by a modern ATA drive are no longer actual physical parameters since the reported numbers are constrained by historic operating-system interfaces and with zone bit recording the actual number of sectors varies by zone. Disks with SCSI interface address each sector with a unique integer number; the operating system remains ignorant of their head or cylinder count.

Hard disk drive manufacturers specify disk capacity using the SI prefixes mega-, giga- and tera-, and their abbreviations M, G and T. Byte is typically abbreviated B.

Some operating-system tools report capacity using the same abbreviations but actually use binary prefixes. For instance, the prefix mega-, which normally means 10⁶ (1,000,000), in the context of data storage can mean 2²⁰ (1,048,576), which is nearly 5% more. Similar usage has been applied to prefixes of greater magnitude. This results in a discrepancy between the disk manufacturer's stated capacity and the apparent capacity of the drive when examined through some operating-system tools. The difference becomes with 7% even more noticeable for a gigabyte. For example, Microsoft Windows reports disk capacity both in decimal-based units to 12 or more significant digits and with binary-based units to three significant digits. Thus a disk specified by a disk manufacturer as a 30 GB disk might have its capacity reported by Windows 2000 both as "30,065,098,568 bytes" and "28.0 GB". The disk manufacturer used the SI definition of "giga", 10⁹ to arrive at 30 GB; however, because the utilities provided by Windows define a gigabyte as 1,073,741,824 bytes (2³⁰ bytes, often referred to as a gibibyte, or GiB), the operating system reports capacity of the disk drive as (only) 28.0 GB.

Form factors

The earliest “form factor” hard disk drives inherited their dimensions from floppy-disk drives (FDDs), so that either could be mounted in chassis slots, and thus the HDD form factors became colloquially named after the corresponding FDD types. "Form factor" compatibility continued after the 3½ in size even though floppy disk drives with new smaller dimensions ceased to be offered.

• "8 inch" drive: (9.5 in x 4.624 in x 14.25 in = 241.3 mm x 117.5 mm x 362 mm)
  In 1979, Shugart Associates' SA1000 was the first form factor compatible HDD, having the same dimensions and a compatible interface to the 8" FDD. Both "full height" and "half height" (2.313 in) versions were available.

• "5¼ inch" drive: (5.75 in x 1.63 in x 8 in = 146.1 mm x 41.4 mm x 203 mm)
  This smaller form factor, first used in an HDD by Seagate in 1980, was the same size as full height 5¼-inch diameter FDD, i.e., 3.25 inches high. This is twice as high as commonly used today; i.e., 1.63 in = 41.4 mm (“half height”). Most desktop models of drives for optical 120 mm disks (DVD, CD) use the half height 5¼" dimension, but it fell out of fashion for HDDs. The Quantum “Bigfoot” HDD was the last to use it in the late 1990s, with “low-profile” (~25 mm) and “ultra-low-profile” (~20 mm) high versions.

• "3½ inch" drive: (4 in x 1 in x 5.75 in = 101.6 mm x 25.4 mm x 146 mm)
  This smaller form factor, first used in an HDD by Rodime in 1984, was the same size as the "half height" 3½ FDD, i.e., 1.63 inches high. Today has been largely superseded by 1-inch high “slimline” or “low-profile” versions of this form factor which is used by most desktop HDDs.

• "2½ inch" drive: (2.75 in x 0.374 in x 3.945 in = 69.85 mm x 9.5 mm x 100 mm)
  This smaller form factor was introduced by PrairieTek in 1988; there is no corresponding FDD. It is widely used today for hard-disk drives in mobile devices (laptops, music players, etc.). Today, the dominant height of this form factor is 9.5 mm, but there were also 19 mm, 17 mm, and 12.5 mm high variants in use.

• "1.8 inch" drive: (54 mm × 8 mm × 71 mm)
  This form factor, originally introduced by Integral Peripherals in 1993, has evolved into the ATA-7 LIF with dimensions as stated. It is increasingly used in digital audio players and subnotebooks. An original variant exists for 2–5 GB sized HDDs that fit directly into a PC card expansion slot.

• "1 inch" drive: (42.8 mm × 5 mm × 36.4 mm)
  This form factor was introduced in 1999 as IBM's Microdrive to fit inside a CF Type II slot.

• "0.85 inch" drive: (24 mm × 5 mm × 32 mm)
  Toshiba announced this form factor in January 2004 for use in mobile phones and similar applications, including SD/MMC slot compatible HDDs optimized for video storage on 4G handsets. Toshiba currently sells a 4 GB (MK4001MTD) and 8 GB (MK8003MTD) version and holds the Guinness World Record for the smallest harddisk drive.

Major manufacturers discontinued the development of new products for the 1-inch and 0.85-inch form factors in 2007, due to falling prices of flash memory.

The inch-based nickname of all these form factors usually do not indicate any actual product dimension (which are for more recent form factors specified in millimeters), but just roughly indicate a size relative to disk diameters, in the interest of historic continuity.

Access and interfaces

Hard disk drives are accessed over one of a number of bus types, including parallel ATA (PATA, also called IDE or EIDE), Serial ATA (SATA), SCSI, Serial Attached SCSI (SAS), and Fibre Channel. Bridge circuitry is sometimes used to connect hard disk drives to buses that they cannot communicate with natively, such as IEEE 1394 and USB.

Back in the days of the ST-506 interface, the data encoding scheme was also important. The first ST-506 disks used Modified Frequency Modulation (MFM) encoding, and transferred data at a rate of 5 megabits per second. Later on, controllers using 2,7 RLL (or just "RLL") encoding increased the transfer rate by 50%, to 7.5 megabits per second; this also increased disk capacity by fifty percent.

Many ST-506 interface disk drives were only specified by the manufacturer to run at the lower MFM data rate, while other models (usually more expensive versions of the same basic disk drive) were specified to run at the higher RLL data rate. In some cases, a disk drive had sufficient margin to allow the MFM specified model to run at the faster RLL data rate; however, this was often unreliable and was not recommended. (An RLL-certified disk drive could run on a MFM controller, but with 1/3 less data capacity and speed.)

Enhanced Small Disk Interface (ESDI) also supported multiple data rates (ESDI disks always used 2,7 RLL, but at 10, 15 or 20 megabits per second), but this was usually negotiated automatically by the disk drive and controller; most of the time, however, 15 or 20 megabit ESDI disk drives weren't downward compatible (i.e. a 15 or 20 megabit disk drive wouldn't run on a 10 megabit controller). ESDI disk drives typically also had jumpers to set the number of sectors per track and (in some cases) sector size.

SCSI originally had just one speed, 5 MHz (for a maximum data rate of five megabytes per second), but later this was increased dramatically. The SCSI bus speed had no bearing on the disk's internal speed because of buffering between the SCSI bus and the disk drive's internal data bus; however, many early disk drives had very small buffers, and thus had to be reformatted to a different interleave (just like ST-506 disks) when used on slow computers, such as early IBM PC compatibles and early Apple Macintoshes.

ATA disks have typically had no problems with interleave or data rate, due to their controller design, but many early models were incompatible with each other and couldn't run in a master/slave setup (two disks on the same cable). This was mostly remedied by the mid-1990s, when ATA's specification was standardised and the details began to be cleaned up, but still causes problems occasionally (especially with CD-ROM and DVD-ROM disks, and when mixing Ultra DMA and non-UDMA devices).

Serial ATA does away with master/slave setups entirely, placing each disk on its own channel (with its own set of I/O ports) instead.

FireWire/IEEE 1394 and USB(1.0/2.0) HDDs are external units containing generally ATA or SCSI disks with ports on the back allowing very simple and effective expansion and mobility. Most FireWire/IEEE 1394 models are able to daisy-chain in order to continue adding peripherals without requiring additional ports on the computer itself.

Acronym	Meaning	Description
SASI	Shugart Associates System Interface	Historical predecessor to SCSI.
SCSI	Small Computer System Interface	Bus oriented that handles concurrent operations.
SAS	Serial Attached SCSI	Improvement of SCSI, uses serial communication instead of parallel.
ST-506		Historical Seagate interface.
ST-412		Historical Seagate interface (minor improvement over ST-506).
ESDI	Enhanced Small Disk Interface	Historical; backwards compatible with ST-412/506, but faster and more integrated.
ATA	Advanced Technology Attachment	Successor to ST-412/506/ESDI by integrating the disk controller completely onto the device. Incapable of concurrent operations.
SATA	Serial ATA	Improvement of ATA, uses serial communication instead of parallel.

Integrity

Due to the extremely close spacing between the heads and the disk surface, any contamination of the read-write heads or platters can lead to a head crash — a failure of the disk in which the head scrapes across the platter surface, often grinding away the thin magnetic film and causing data loss. Head crashes can be caused by electronic failure, a sudden power failure, physical shock, wear and tear, corrosion, or poorly manufactured platters and heads.

The HDD's spindle system relies on air pressure inside the enclosure to support the heads at their proper flying height while the disk rotates. An HDD requires a certain range of air pressures in order to operate properly. The connection to the external environment and pressure occurs through a small hole in the enclosure (about 0.5 mm in diameter), usually with a carbon filter on the inside (the breather filter, see below). If the air pressure is too low, then there is not enough lift for the flying head, so the head gets too close to the disk, and there is a risk of head crashes and data loss. Specially manufactured sealed and pressurized disks are needed for reliable high-altitude operation, above about 3,000 m (10,000 feet). Note that modern commercial aircraft have a pressurized cabin, whose pressure altitude does not normally exceed 2,600 m(8,500 feet) - thus, ordinary hard drives can safely be used in flight. Modern disks include temperature sensors and adjust their operation to the operating environment. Breather holes can be seen on all disks — they usually have a sticker next to them, warning the user not to cover the holes. The air inside the operating disk is constantly moving too, being swept in motion by friction with the spinning platters. This air passes through an internal recirculation (or "recirc") filter to remove any leftover contaminants from manufacture, any particles or chemicals that may have somehow entered the enclosure, and any particles or outgassing generated internally in normal operation. Very high humidity for extended periods can corrode the heads and platters.

For giant magnetoresistive (GMR) heads in particular, a minor head crash from contamination (that does not remove the magnetic surface of the disk) still results in the head temporarily overheating, due to friction with the disk surface, and can render the data unreadable for a short period until the head temperature stabilizes (so called "thermal asperity," a problem which can partially be dealt with by proper electronic filtering of the read signal).

The hard disk's electronics control the movement of the actuator and the rotation of the disk, and perform reads and writes on demand from the disk controller. Modern disk firmware is capable of scheduling reads and writes efficiently on the platter surfaces and remapping sectors of the media which have failed.

Landing zones and load/unload technology

Most HDDs prevent power interruptions from shutting the drive down with its heads landing in the data zone by either moving the heads to a landing zone or unloading (i.e., load/unload) the heads.

A landing zone is an area of the platter usually near its inner diameter (ID), where no data is stored. This area is called the Contact Start/Stop (CSS) zone. Disks are designed such that either a spring or, more recently, rotational inertia in the platters is used to park the heads in the case of unexpected power loss.

Spring tension from the head mounting constantly pushes the heads towards the platter. While the disk is spinning, the heads are supported by an air bearing and experience no physical contact or wear. In CSS drives the sliders carrying the head sensors (often also just called heads) are designed to survive a number of landings and takeoffs from the media surface, though wear and tear on these microscopic components eventually takes its toll. Most manufacturers design the sliders to survive 50,000 contact cycles before the chance of damage on startup rises above 50%. However, the decay rate is not linear: when a disk is younger and has had fewer start-stop cycles, it has a better chance of surviving the next startup than an older, higher-mileage disk (as the head literally drags along the disk's surface until the air bearing is established). For example, the Seagate Barracuda 7200.10 series of desktop hard disks are rated to 50,000 start-stop cycles. This means that no failures attributed to the head-platter interface were seen before at least 50,000 start-stop cycles during testing.

Around 1995 IBM pioneered a technology where a landing zone on the disk is made by a precision laser process (Laser Zone Texture = LZT) producing an array of smooth nanometer-scale "bumps" in a landing zone, thus vastly improving stiction and wear performance. This technology is still largely in use today (2007), predominantly in desktop and enterprise (3.5 inch) drives. In general, CSS technology can be prone to increased stiction (the tendency for the heads to stick to the platter surface), e.g. as a consequence of increased humidity. Excessive stiction can cause physical damage to the platter and slider or spindle motor.

Load/Unload technology relies on the heads being lifted off the platters into a safe location, thus eliminating the risks of wear and stiction altogether. The first HDD RAMAC and most early disk drives used complex mechanisms to load and unload the heads. Modern HDDs use ramp loading, first introduced by Memorex in 1967, to load/unload onto plastic "ramps" near the outer disk edge.

All HDDs today still use one of these two technologies. Each has a list of advantages and drawbacks in terms of loss of storage area on the disk, relative difficulty of mechanical tolerance control, cost of implementation, etc.

Addressing shock robustness, IBM also created a technology for their ThinkPad line of laptop computers called the Active Protection System. When a sudden, sharp movement is detected by the built-in accelerometer in the Thinkpad, internal hard disk heads automatically unload themselves to reduce the risk of any potential data loss or scratch defects. Apple later also utilized this technology in their PowerBook, iBook, MacBook Pro, and MacBook line, known as the Sudden Motion Sensor. Toshiba has released similar technology in their laptops.

Disk failures and their metrics

Most major hard disk and motherboard vendors now support self-monitoring, analysis and reporting technology (S.M.A.R.T.), which attempts to alert users to impending failures.

However, not all failures are predictable. Normal use eventually can lead to a breakd

own in the inherently fragile device, which makes it essential for the user to periodically back up the data onto a separate storage device. Failure to do so can lead to the loss of data. While it may be possible to recover lost information, it is normally an extremely costly procedure, and it is not possible to guarantee success. A 2007 study published by Google suggested very little correlation between failure rates and either high temperature or activity level. While several S.M.A.R.T. parameters have an impact on failure probability, a large fraction of failed drives do not produce predictive S.M.A.R.T. parameters. S.M.A.R.T. parameters alone may not be useful for predicting individual drive failures.

SCSI, SAS and FC drives are typically more expensive and are traditionally used in servers and disk arrays, whereas inexpensive ATA and SATA drives evolved in the home computer market and were perceived to be less reliable. This distinction is now becoming blurred.

The mean time between failures (MTBF) of SATA drives is usually about 600,000 hours (some drives such as Western Digital Raptor have rated 1.2 million hours MTBF), while SCSI drives are rated for upwards of 1.5 million hours. However, independent research indicates that MTBF is not a reliable estimate of a drive's longevity. MTBF is conducted in laboratory environments in test chambers and is an important metric to determine the quality of a disk drive b

efore it enters high volume production. Once the drive product is in production, the more valid metric is annualized failure rate (AFR). AFR is the percentage of real-world drive failures after shipping.

SAS drives are comparable to SCSI drives, with high MTBF and high reliability.

Enterprise SATA drives designed and produced for enterprise markets, unlike standard SATA drives, have reliability comparable to other enterprise class drives.

Typically enterprise drives (all enterprise drives, including SCSI, SAS, enterprise SATA and FC) experience between .70%-.78% annual failure rates from the total installed drives.

Manufacturers

The technological resources and know-how required for modern drive development and production mean that as of 2007, over 98% of the world's HDDs are manufactured by just a handful of large firms: Seagate (which now owns Maxtor), Western Digital, Samsung, and Hitachi (which owns the former disk manufacturing

division of IBM). Fujitsu continues to make mobile- and server-class disks but exited the desktop-class market in 2001. Toshiba is a major manufacturer of 2.5-inch and 1.8-inch notebook disks. ExcelStor is a small HDD manufacturer.

Dozens of former HDD manufacturers have gone out of business, merged, or closed their HDD

divisions; as capacities and demand for products increased, profits became hard to find, and the market underwent significant consolidation in the late 1980s and late 1990s. The first notable casualty of the business in the PC era was Computer Memories Inc. or CMI; after an incident with faulty 20 MB AT disks in 1985, CMI's reputation never recovered, and they exited the HDD business in 1987. Another notable failure was MiniScribe, who went bankrupt in 1990 after it was found that they had engaged in accounting fraud and inflated sales numbers for several years. Many other smaller companies (like Kalok, Microscience, LaPine, Areal, Priam and PrairieTek) also did not survive the shakeout, and had disappeared by 1993; Micropolis was able to hold on until 1997, and JTS, a relative latecomer to the scene, lasted only a few years and was gone by 1999, after atte

mpting to manufacture HDDs in India. Their claim to fame was creating a new 3" form factor drive for use in laptops. Quantum and Integral also invested in the 3" form factor; but eventually gave up as this form factor failed to catch on. Rodime was also an important manufacturer during the 1980s, but stopped making disks in the early 1990s amid the shakeout and now concentrates on technology licensing; they hold a number of patents related to 3.5-inch form factor HDDs.

• 1988: Tandem Computers sold its disk manufacturing division to Western Digital (WDC), which was then a well-known controller designer.
• 1989: Seagate Technology bought Control Data's high-end disk business, as part of CDC's exit from hardware manufacturing.
• 1990: Maxtor buys MiniScribe out of bankruptcy, making it the core of its low-end disk division.
• 1994: Quantum bought DEC's storage division, giving it a high-end disk range to go with its more consumer-oriented ProDrive range, as well as the DLT tape drive range.
• 1995: Conner Peripherals, which was founded by one of Seagate Technology's co-founders along with personnel from MiniScribe, announces a merger with Seagate, which was completed in early 1996.
• 1996: JTS merges with Atari, allowing JTS to bring its disk range into production. Atari was sold to Hasbro in 1998, while JTS itself went bankrupt in 1999.
• 2000: Quantum sells its disk division to Maxtor to concentrate on tape drives and backup equipment.
• 2003: Following the controversy over mass failures of its Deskstar 75GXP range, HDD pioneer IBM sold the majority of its disk division to Hitachi, who renamed it Hitachi Global Storage Technologies (HGST).
• December 21, 2005: Seagate and Maxtor announced an agreement under which Seagate would acquire Maxtor in an all stock transaction valued at $1.9 billion. The acquisition was approved by the appropriate regulatory bodies, and closed on May 19, 2006.
• 2007
• April: Hitachi releases the 1 TB Hitachi Deskstar 7K1000 (1TB = 1 trillion bytes, roughly 931.5 GiB).
• July: Western Digital (WDC) acquires Komag U.S.A, a thin-film media manufacturer, for USD 1 Billion.
• September: Hitachi releases 2.5-inch 320 GB hard disk.
• 2008
• January: Hitachi releases 2.5-inch 500 GB hard disk and it was demonstrated by Asus with a laptop at 1 TB storage in CES event, Las Vegas

History

For many years, HDDs were large, cumbersome devices, more suited to use in the protected environment of a data center or large office than in a harsh industrial environment (due to their delicacy), or small office or home (due to their size and power consumption). Before the early 1980s, most HDDs had 8-inch (20 cm) or 14-inch (35 cm) platters, required an equipment rack or a large amount of floor space (especially the large removable-media disks, which were often referred to as "washing machines"), and in many cases needed high-current or even three-phase power hookups due to the large motors they used. Because of this, HDDs were not commonly used with microcomputers until after 1980, when Seagate Technology introduced the ST-506, the first 5.25-inch HDD, with a capacity of 5 megabytes. In fact, in its factory configuration, the original IBM PC (IBM 5150) was not equipped with a hard disk drive.

Most microcomputer HDDs in the early 1980s were not sold under their manufacturer's names, but by OEMs as part of larger peripherals (such as the Corvus Disk System and the Apple ProFile). The IBM PC/XT had an internal HDD, however, and this started a trend toward buying "bare" disks (often by mail order) and installing them directly into a system. Hard disk drive makers started marketing to end users as well as OEMs, and by the mid-1990s, HDDs had become available on retail store shelves.

While internal disks became the system of choice on PCs, external HDDs remained popular for much longer on the Apple Macintosh and other platforms. The first Apple Macintosh built between 1984 and 1986 had a closed architecture that did not support an external or internal hard drive. In 1986, Apple added a SCSI port on the back, making external expansion easy. External SCSI drives were also popular with older microcomputers such as the Apple II series, and were also used extensively in servers, a usage which is still popular today. The appearance in the late 1990s of high-speed external interfaces such as USB and FireWire has made external disk systems popular among PC users once again, especially for laptop users, users who install Linux in the additional external unit and users who move large amounts of data between two or more areas. Most HDD makers now make their disks available in external cases.